Sichuan Nanshan Powder Actuated Fastening System co., Ltd.

Nylon Style

Nylon Nail Anchors are ideal for a wide variety of light load fastening in wood.Hardboard,plaster, metal,cinder block,brick,slate,marble,plastic, tile,glass and concrete.Its unique design allows the nail to expand the anchor uniformly in the hole.
Nylon Anchors

The frame anchors for window and door frames.

For fixing of plastic,wood,aluminum window and door frames to concrete,brick,hollow blocks and cheeker brick.Yellow Zinc plated passivated steel screw with special pozi.

Drive head adapted to receive push-in caps of various colors.Cap colors:white,dark brown,gray.
Gravity/Spring Toggle Anchors

For fixing of concrete,solid bricks,perforated bricks,hollow blocks.

The fixings are manufactured from the same highgradpe and quality-monitored polyimide(nylon)which is also used for the frame fixings with general building inspectorate approval.The material is temperature resistant-40~+80℃.

Preassembled for quick and easy installation.High holding power.
PM-A-Gravity/Spring Toggle Anchors

Heavy gauge wings is high capacity true design.

For fixing to cavity walls and ceiling of low stuctural strength.

Any screw head and wing available as your requirement.
PM-A-Toggle Bolts

Heavy gauge wings…high capacity true design.

Durable music wire spring…positive spring wing action.Easy tightening under load…no bilding on screw.
Any screw head available as your requirement.

The test values listed were obtained using 200-250kgs/cm2concrete(no aggregate).

A safe working load should not exceed 25% of stated value.
PM-A-Slight Sleeve Anchors Steel

For fixing of concrete,solid bricks,perforated bricks,hollow blocks.

Any screw head available as your requirement.

Preassembled for quick and easy installation.High holding power.
PM-A-Hollow Wall Anchors

Hollow wall Anchors securely fasten mirrous,pictures,
cabinets,cutrain-drapes-shelf brackets,bathroom fi-
xtures,to hollow walls of plaster over wood lath or metallath,wallboard,gypsum ior cinder block,hollow tile,etc.Fixtures can be removed or replaced for redecoratingwithout disturbing the Hollow Wall Anchors.
PM-A-Heavy Duty Shell Anchors

HEAVY DUTY SHELL ANCHOR 4 pcs shells made of,Steel pressed used to dirt & moisture is appreciated.

High retaining power & can be removed easily.

When tightening the nut or screw the conical section is pulled into the anchor shells expanding it & weding it inside the anchor base.
PM-A-Tie Anchors

TIE WIRE ANCHOR is quick to install & easily set by pulling back with claw hammer.

Strong holding power specifically designed to protect anchorage point in concrete ceiling.

Suitable for:suspended ceiling & lightweight suspension.
Ie hanging overhead signs.
PM-A-Chemical Anchors Studs

Studs in stainless steel and yellow zinc plated steel.

Heavy duty fixing without radial influence of expansion forces can be used close to edges.

Accurate drill depth is necessary.

Fully loadable after the prescribed hardening-setting time.
PM-A-Stud Anchors

Stud anchor is quick & easily to install & set plug in with hammer.

Strong holding power special designed to THREAD DIA=ANCHOR DIA=DRILL HOLE DIA.
PM-A-Hit Anchors

HIT ANCHOR is a fast & easy to use expansion
anchor.NO precise hole depth is required and installation condition can be adjusted from pin
and nut.
PM-A-Wedge Anchors

Not require precise hole depth or hole cleaning out.
Anchor can be hammered below the surface of the
concrete when no longer needed.
The one piece clip is formed around Anchor,assuring
full expansion for dependable,superior holding prower.Expanding clip will not fall off or twist in the hole.
PM-A-Sleeve Anchors

Preassembled for quick and easy installation,can be used in thin sections of concrete or solid masonry.
Head styles for every application.
The test values listed were obtained using 200-250kgs/cm2 concrete (no aggregate). A safe working load should not exceed 25% of stated values.
PM-A-Sleeve Anchors

The screws of the anchor have been manufactured under the DIN-933 standard and their quality-hardness is 6.8(i.e.60 to 80 kg./mm)
The washer is wide,which gives a bigger allowance for pieces or structures to be fastened.
While performing the fixing of the anchor,the plastic part or ring gets deformed,which fills and blocks the hole of the piece or structure to be fastened;this plastics absorbs material irregularities,and-in addittion-it is a useful damp-proof piece to protect the inner mechanism of the anchor.
Any screw head available as your requirement.
The cone has some grooves(milling)in order to prevent the anchor from loose or spin movement after fixing into the hole and ready to expansion.
PM-A-Sleeve Anchors

Preassembled for quick and easy installation,can be used in thin sections of concrete of solid masonry.
Head styles for every application.
The test values listed were obtained using 200-250kgs/cm2concrete (on aggregate).A safe working load should not execeed 25%of stated values.
PM-A-Heavy Duty Expansion Anchors

Preassembled for quick and easy installation high holding power by tough Expanding sleeve and anchor sleeve can be used in heavy duty applications.
Versatile and durable.
Nut dished apring washer and flat washer are pre-assembled.
A safe working load should not exceed 25% of stated value.
PM-A-Bolt Anchors

Preassembled for quick and easy installation,High holding power by tough sleeve can be used in heavy duty applications. Vibration resistance. Preassembled for quick and easy installation,High holding power by tough sleeve can be used in heavy duty applications.
Vibration resistance.
Versatile and durable.
Nut spring washer and washer are preassembled.
PM-A-Self Drill Anchors

The anchor body with prongs on the end can be used for drilling with tool.
Self Drill anchor is an improved expansion Anchor with internal Thread and a Plug,and is the most popular Anchor.
Anchor can be installed with Hex Bolt,Stud and Hookbolt,etc.After installation,concrete will not be effected in appearance as a rise on the surface.
PM-A-Cut Anchors

CUT ANCHOR is an improved expansion Anchor with internal Thread and a Plug,and is the most popular Anchor.
Anchor can be installed with Hex Bolt,Stud and Hookbolt,etc.After installation,concrete will not be effected in appearance as a rise on the surface.
PM-A-DRI-20

Perfect expansion and specially designed built-in plug ensures full expansion of anchor.
PM-A-DRI-20

Perfect expansion and specially designed built-in plug ensures full expansion of anchor.


	Sichuan Nanshan Powder Actuated Fastening System co., Ltd Address: Nanxi, Yibin, Sichuan of China
	Zip Code: 644100 Tel: +86 831 3335316 Fax: +86 831 3335416 Email: sales@nanshanpaf.com
	中文│Please Contact us with more details.
	Copyright © 2011, Nanshan All rights 蜀ICP备05014103号-1 四川南山射钉紧固器材有限公司